Free Fabora tool

Rolling Offset Calculator

A rolling offset is a pipe offset that moves up or down and sideways at the same time. To size it, find the true offset first: the square root of set squared plus roll squared. Then multiply the true offset by the constant for your fitting angle to get the travel, which is the center-to-center length of the angled pipe. For 45° elbows the constant is 1.414.

Rolling offset calculator

Enter what you know

Type of offset
Fitting angle

Use a decimal or a fraction, like 12, 12.5, 12 1/2 or 1-1/2. The angle is the angle of the fitting, more than 0 and less than 90 degrees.

True offset, travel and run

True offset15 in

15.00 in. The square root of set squared plus roll squared.

Travel21 3/16 in

21.21 in. Center to center of the two fittings.

Run15 in

15.00 in. How far the offset takes up along the pipe.

How it is worked out

True offset = √(12² + 9²) = 15 in. Travel = 15 × 1.414 = 21.21 in. Run = 15 × 1.000 = 15 in.

What is the multiplier for a 45 degree offset?

The multiplier for a 45 degree offset is 1.414. Multiply the offset by 1.414 to get the travel. The run is the same as the offset, because a 45° triangle has two equal sides.

Example

A 10 in offset with 45° elbows has a travel of 10 × 1.414 = 14.14 in, which is 14 1/8 in. The run is 10 in.

Offset multiplier chart

Travel = offset × travel multiplier. Run = offset × run multiplier. For a rolling offset, use the true offset.

Travel and run multipliers by fitting angle
Fitting angleTravel multiplierRun multiplier
60°1.1550.577
45°1.4141.000
30°2.0001.732
22.5°2.6132.414
11.25°5.1265.027
5.625°10.20210.153

The travel multiplier is 1 divided by the sine of the angle (the cosecant). The run multiplier is 1 divided by the tangent (the cotangent).

How do you calculate a rolling offset?

  1. Measure the set: how far the pipe rises or drops.
  2. Measure the roll: how far it moves sideways.
  3. Find the true offset: √(set² + roll²).
  4. Multiply the true offset by the travel multiplier for your fittings. That is the travel.
  5. Multiply the true offset by the run multiplier. That is the run, the distance the offset takes up along the line of the pipe.

Example

The set is 12 in and the roll is 9 in. The true offset is √(144 + 81) = 15 in. With 45° elbows the travel is 15 × 1.414 = 21.21 in, about 21 3/16 in, and the run is 15 in.

What is the rolling offset formula?

  • True offset = √(set² + roll²)
  • Travel = true offset ÷ sin(fitting angle)
  • Run = true offset ÷ tan(fitting angle)

With 45° fittings that shortens to travel = true offset × 1.414.

What is the difference between an offset and a rolling offset?

A simple offset moves the pipe in one direction only: up, down or sideways. A rolling offset moves it in two directions at once, so the two elbows sit rolled at an angle instead of flat. The math is the same once you have the true offset. A simple offset skips step 3, because the offset you measured is already the true offset.

How do you get the cut length from the travel?

Travel is measured center to center, so the pipe you cut is shorter. Take off one take-out for each elbow: cut length = travel minus 2 × take-out. Allow for your weld gaps or thread engagement as well.

Example

2 in pipe with long-radius 45° butt-weld elbows. ASME B16.9 gives a take-out of 1 3/8 in for that elbow. A 21.21 in travel gives 21.21 - 2.75 = 18.46 in, about 18 7/16 in, before weld gaps.

Take-outs change with pipe size and fitting type, so check the fittings you have in your hand before you cut.

In the Steel Tools app

The Pipe Offset Calculator in Fabora Steel Tools does the whole job on your phone, with no signal needed:

  • travel, run and cut length for simple and rolling offsets
  • long-radius 45° and 90° elbow take-outs to ASME B16.9 looked up by pipe size, 1/2 in to 12 in
  • a "find the angle" helper: enter the offset and the travel or run you have room for, and it gives the angle and the nearest standard fitting
  • the roll angle of the elbows, a 3D picture of the offset and a cut sheet to share
  • inches with fractions, or millimeters
  • saved offsets, so the numbers are still there when you get back to the saw

Pipe Offset is part of Fabora Pro. Steel Tools is free to download for iPhone and Android and has free tools for steel weight, unit conversion, gas bottle life and weld faults.

Rolling offset questions

What is the 1.414 formula?

1.414 is the square root of 2. It is the travel multiplier for 45° fittings: travel = offset × 1.414.

What is the multiplier for a 22.5 degree offset?

2.613 for the travel and 2.414 for the run. An 8 in offset with 22.5° elbows has a travel of 20.90 in (20 7/8 in) and a run of 19.31 in (19 5/16 in).

What is the multiplier for a 60 degree offset?

1.155 for the travel and 0.577 for the run.

What is the multiplier for a 30 degree offset?

2.000 for the travel and 1.732 for the run.

Does the multiplier change with pipe size?

No. The multipliers come from the fitting angle alone. Pipe size changes the elbow take-out, which changes the cut length.

Does this work for conduit, copper and PVC?

Yes. The same right-triangle math applies to any pipe, tube or conduit run that uses two fittings or bends of the same angle.

Is the travel the length of pipe I cut?

No. Travel is center to center. Subtract the take-out of both fittings to get the cut length.

Last updated: November 16, 2026. Multipliers are exact trigonometry rounded to three decimal places. Elbow take-outs quoted from ASME B16.9; always confirm against the actual fittings.

Fabora Steel Tools

Pipe Offset Calculator in Fabora Steel Tools

The Pipe Offset Calculator in Fabora Steel Tools does the whole job on your phone, with no signal needed. Pipe Offset is part of Fabora Pro.

Works offlineInches and mm